Plumber Bondi Logo

0402 290 290

  • HOME
  • BLOCKED DRAINS
  • HOT WATER
  • EMERGENCY PLUMBING
  • PIPE RELINING
×
  • HOME
  • BLOCKED DRAINS
  • HOT WATER
  • EMERGENCY PLUMBING
  • PIPE RELINING

The Best Ways to Save Water in the Bathroom

You may have been making every effort to reduce household water consumption. This is a great mindset to have because you can save money on your water costs while also helping the environment. The bathroom is probably the most water-intensive room in any home. After all, this is where you shower and flush waste down the toilet with a lot of water. Logically, this is a critical area to which you must devote the most amount of attention in your daily routine. Here are some suggestions for conserving water in the bathroom.

No water should be left running.

Allowing water to run without being used is a simple way to waste water. Brushing one’s teeth or wiping one’s face usually causes this. You may believe it has little effect on water use, but did you realize that doing so on a regular basis can waste thousands of gallons of water each year? This is why you should be cautious when using your home’s faucets.

Reduce the amount of time you spend in the bath and shower.

Baths or showers? Showers, rather than baths, are a better way to preserve water because they require less water. Showering for an extended period of time, on the other hand, will not save any water, so keep track of how much time you spend in the shower. Shower for no more than five to ten minutes. Those who enjoy long showers may be upset by this suggestion, but if you want to conserve water, you must make modest sacrifices.

Water-saving units should be used to replace old plumbing fixtures.

Because being eco-friendly is so fashionable these days, appliance manufacturers are competing to create the most efficient yet environmentally friendly fixtures. This method of water conservation may be costly at first, but it will save you money in the long run. It is highly desirable to replace your old plumbing appliances with new fixtures that can save water. Dual flush toilets can be used to replace ordinary toilets. The dual flush feature lets you to save more water by regulating the amount of liquid used. It saves water by using less for liquid waste and more for solid garbage.

Installing low-flow faucets and showerheads, which use less water than normal counterparts, is also a good idea. Some may believe that it may result in less water flow, however this is not the case. Its design is so unique that even though it uses less water, it maintains a constant water pressure.

Don’t Ignore Plumbing Issues

If there are any leaks or the faucet is constantly dripping, you should address them as soon as possible. This will not only destroy your plumbing fixtures, but it will also waste thousands of litres of water. If you don’t know how to fix these fittings, it’s highly recommended that you hire a plumber.

Filed Under: Emergency Plumbing, Hot Water

How to Make an Elderly-Friendly Bathroom

Due to physical constraints imposed by their age, the elderly may have difficulty using the restroom. Showering, going to the bathroom, and other bathroom routines can be difficult for them. In fact, because of the potential of slipping, it can be quite dangerous for the elderly. Fortunately, you can upgrade your bathroom with new attachments and features to make it more senior-friendly.

Use non-slip rugs and floor coverings.

This is beneficial not only to the elderly, but to everyone who uses the restroom. It does not necessitate any difficult work or costly renovation, making it a quick and simple answer. Non-slip tapes can also be used on the lower tub and shower pans.

Set up Grab Bars

Old people have a tough time moving to the bathroom due to limited mobility. You can improve their manoeuvrability by adding grab bars on the showers, toilet, and bathtub. Installing the bars can be done on your own but if you’re not handy with tools or not confident to install it on your own, then just hire another person to do the installation for you. It’s best to put the grab bars on accident-prone areas like the shower area, toilet, and the entrance of the bathroom.

Change Your Faucet

Some elderly people have difficulty turning faucet handles. Installing taps that are more elder-friendly, such as foot-operated and lever varieties, can make things easier for them. However, you must consider which faucet is appropriate for the elderly person’s physical limitations. Consult your local plumber for more information on what to install and where to put it before making a decision.

Increase the Toilet Height

Some elderly persons may find it difficult to use the restroom. It’s possible that the towel’s height no longer matters to them. The remedy is to raise the toilet seat height. Replacing the toilet with a new one with a “comfort height” is an expensive but useful option if you want to refurbish the bathroom. Install a thick seat to boost the height for a quick remedy.

Walk-In Bathtubs and Curbless Showers

If the elderly person has problems utilizing their legs or is in a wheelchair, you should make your shower curbless to accommodate their needs. As you can see, the curbs can make it difficult for the older to get to the shower. Bathtubs with walk-in doors are a great alternative to ordinary bathtubs. A walk-in bathtub has a basic design: it features a “mini door” that allows the elderly to enter the tub with ease.

Well-illuminated bathroom

The majority of the elderly have vision difficulties. You may be able to see everything clearly, but most elderly folks will struggle to navigate if the room isn’t properly lit. Bright lights should be installed in the shower area, toilet, and, most importantly, the room’s entrance.

Filed Under: Emergency Plumbing, Hot Water

How Hot Water Systems Work?

Many appliances and developments help to make a home more comfortable and luxurious. A water heater is one of them. What makes this appliance so fascinating is that the mechanisms are so intricate that it necessitates the use of specialized personnel to do any repairs or replacements. This is a preventive measure designed to keep homeowners and thrifty do-it-yourselfers from messing with the equipment and harming it. You must learn the parts and operations of the water heater firsthand in order to gain a better understanding of it. That is exactly what you will learn in this post. Here’s a quick rundown of how the process works and how the water heater works:

Storage

The first stage in the water heater’s procedure is to ensure that it has enough water to heat. Some water heating models require a specific length of time to amass water inside a tank and then a few minutes to heat it. Heating coils strategically positioned at the bottom of the tank near the supply pipe heat the water as it enters the tank, ensuring that the water near the rim is already insulated and hot while the water entering the tank receives the same treatment. The process continues indefinitely as long as there is a demand for hot water.

The temperature of the water is maintained with the help of a thermostat. This is to ensure that the water flowing from the pipe does not become excessively cold, nor does it burn you. It’s also in charge of controlling the amount of gasoline delivered to the tank for heating.

Toxic emissions are subsequently sent from the burner to the building’s exhaust pipes. Fan-assisted vents are found on various tanks and water heaters to carry the byproduct of water insulation.

Reload

The tank refills through the diffuser tube at the bottom and is heated through the heating coils under the tank as the water travels from the tank to the connecting pipes that lead to the tap.

With so many processes, anode rods are used to manage the corrosive characteristics of the water that comes in the form of minerals and sediments.

Release

All that is done, then by the time you open your tap, there will be freshly heated water at your disposal. Remember that the amount of time a water heater is able to heat up the water supply is dependent on the amount of water there is to be heated as well as the type of water heater that you are using.

Filed Under: blog, Hot Water

Water Heater Maintenance in 6 Easy Steps

Most homeowners neglect the importance of cleaning the water heater on a regular basis, especially if it is used frequently. Don’t get me wrong: underused water heaters aren’t always less damaged than those that are used frequently. In fact, both of them have an equal risk of being injured. It all relies on the appliance’s location, way of use, and overall quality. If you look closely, you’ll notice that we sometimes take for granted things that are very important to us. Just because they’re working correctly now doesn’t ensure they’ll continue to do so tomorrow.

Water heaters provide hot water to keep you warm throughout the colder months. It is not a smart idea to go through the winter without a water heater; it will almost certainly result in tragedy and major health problems. This is why you should be on the lookout for any problems with your water heater.

Prevention is preferable to cure, as the saying goes. So, here are some suggestions for keeping your water heater in good working order:

Adjust the temperature.

Check your water heater’s temperature. Don’t make it any higher than it needs to be. Make sure the temperature is between 120 and 130 degrees. This preventive approach will help to keep the water heater from overworking itself and causing harm to the device. Also, keep in mind that lowering the temperature by 10 degrees reduces your energy consumption by 5%. This procedure, in theory, not only keeps your heating unit safe, but it also saves you from going broke.

Check the clearance.

Check the clearance of your water heater on a daily basis. Make sure there’s at least 12 feet between it and the nearest appliance or wall. Keeping the equipment at a safe distance can help you avoid harm from overheating mechanisms. Its allowance around the body aids in temperature regulation and keeps the machine cool.

Drain the tank occasionally.

Make it a practice to empty the tank’s contents at least six times a year. To be safe, repeat this process once a month. This action will extend the unit’s shelf life and improve its performance.

Turn off the water main first. Connect a garden hose to the drain valve and empty the contents into a bucket. You can utilize the water to water your plants and clean up your yard. When you’ve finished emptying the tank, clean it and begin filling it again, keeping the garden hose connected to drain the contents. You can now close it and turn on the water heater again once the water is clear. If the water remains hazy, open the water supply valve and stir or crack the deposits to allow them to be conveyed in the water to the bucket.

Test the temperature-pressure relief valve.

Keep in mind to remove this fixture at least three times a year. Make sure everything, especially the temperature and pressure setting, is in moderation. Failure to do so will almost surely result in leaking valves and fractured pipes.

Filed Under: blog, Hot Water

4 Water Heater Maintenance Tips

Whether we utilize expensive or low-cost ways, all of our appliances need be maintained. These techniques will ensure that our machines function effectively and without causing us any inconvenience. In addition, maintenance is utilized to discover plumbing problems in their early stages, allowing you to inspect and correct them right away. Here are some helpful hints for you to keep in mind:

Drain the tank

Water heater tanks should be drained at least once a year. This is done to remove any sediments that are preventing the burner from boiling the water. This procedure ensures that your machine will run smoothly. Draining our tanks is a low-cost technique to keep the device running.

  • Before you do anything, turn off the water heater.
  • Use a garden hose to connect to the drain valve, which is normally located near the bottom of the tank.
  • Close the water valve to stop the water from pouring into the tank.
  • The relief valve can be unlocked to break the valve.
  • Open the drain valve.
  • Sediments will pour out of the tank after the drain valve is opened. After that, reverse the steps. Make certain that the electricity or gas is turned off before filling the tank with water.

Insulate water heater

Insulating your water heater isn’t just for maintenance; it can also help you save money on your monthly electricity bill. Most people believe that pipes are the only ones that need to be insulated, however this is incorrect. Insulation is also required for our water heater. This will not only lower your bill, but it will also avoid heat loss. Households that utilize new water heater models, on the other hand, are no longer required to use insulation.

Decrease temperature

The temperature of our water heater, according to experts, should be between 115 and 120 degrees Fahrenheit. You will save energy by using this strategy, and your unit will not overheat and explode as a result. In addition, energy usage is reduced. If you use a water heater at home, you should be aware that if the temperature inside the tank becomes too high, your water pipes will likely expand. As a result, the tank will develop cracks and leaks, or worse, burst. With this level of care, you can rest assured that you will never have to deal with crack tanks again.

Replace anode rod

The sacrificial anode rod is another name for this element of our water heater. Brass or magnesium can be used to create the rod. After years of use, the rod will need to be replaced. The reason for this is that water substances generate an electrochemical reaction that causes the component to corrode and become less efficient, even if it is not malfunctioning. If you wish to replace the rod, make sure you get one right away if you don’t want your water tank to look like the rod.

Filed Under: blog, Hot Water

4 Things to Try if Your Gas Water Heater Isn’t Working

There are many different types of water heaters on the market, each with its unique set of characteristics and features that cause them to run and require different maintenance procedures. Apart from that, each of them has their own set of problems. They, like your gas water heater, are prone to malfunctioning from time to time. As a result, it must be addressed and corrected as soon as possible in order to avoid further system problems. The most common problem with a gas water heater is that it constantly fails to heat the domestic water. When the temperature drops below zero, this is a common occurrence. Here are some resources to assist you in resolving this issue. The domestic water is not heated by the gas water heater. There are numerous variables that lead to the emergence of the difficulty when your water heater does not heat the home, and here are some of them:

  • Make sure the water heater’s gas is turned on.

The loss of electricity is usually the primary cause of a mechanism’s failure to operate. In this situation, the gas that powers the device aids its operation. First, try switching the gas knob to pilot mode to prevent the burner from lighting and causing a gas leak while you check the unit’s condition. Then, remove the metal cover from the bottom of the device and check to see if the pilot light and the burner are both lighted.

  • The heater’s pilot light has gone out.

Some water heaters feature instructions on the tank that must be followed in order to avoid future issues. When the gas inlet valve can be partially shut off, this condition may arise. Before relighting the pilot, make sure the handle is parallel to the line and turned completely on. If the pilot still won’t light after you’ve done all of this, it’s merely a sign that the thermocouple may be malfunctioning. To avoid fully blowing out the system, it’s advisable to hire a professional plumber.

  • The Burner Isn’t Turned On

If the burner is not turned on, try changing the cover and making sure the thermostat is set to a safe temperature of 120 to 130 degrees Fahrenheit. Whether it doesn’t work, try turning on your hot tap and waiting a few minutes to see if hot water has already been generated.

  • The smell of gas penetrates the area.

If the system smells like gas, check your water heater straight away and turn the gas valve off right away to stop the flow of gas. There could be a gas leak someplace, and if you don’t flip the valve quickly enough, it could spark a neighboring fire, resulting in an explosion.

Filed Under: blog, Hot Water

  • 1
  • 2
  • 3
  • …
  • 5
  • Next Page »

Book a Job

Or Request For Expert Advice
This field is for validation purposes and should be left unchanged.
bondi logo large

Bondi NSW 2026 Australia

Phone : 0402 290 290
Email : i[email protected]

QUICK LINKS

  • Home
  • About Us
  • Testimonials
  • CONTACT US

SERVICES

  • BLOCKED DRAINS
  • HOT WATER
  • EMERGENCY PLUMBING
  • PIPE RELINING

GOT A QUESTION?

© Copyright 2023 Plumbing Service. All Rights Reserved.

Terms & Condition | Privacy Policy

Designed & Developed by: plumber bondi